Page 1 of 1

500 Gallon Reverse Flow

PostPosted: Tue Sep 20, 2011 3:33 am
by solaryellow
It has been killing me not to work on my dry curing chamber but this beast has been in the way.

Image

Today it finally found its way onto a trailer so I can get back to what I really want to pursue.

Image

Just have to crank out 100 lbs of kielbasa on Thursday for the festival we are vending on Saturday and then hopefully it will be back to the dry curing chamber.

PostPosted: Tue Sep 20, 2011 8:34 am
by DanMcG
That smoker is a monster Joel. Good luck with your first vending gig!

PostPosted: Tue Sep 20, 2011 11:03 am
by NCPaul
What do you mean by reverse flow? That smoker will have no trouble doing a 100 pounds of kielbasa. :D

PostPosted: Tue Sep 20, 2011 12:07 pm
by solaryellow
DanMcG wrote:That smoker is a monster Joel. Good luck with your first vending gig!


Thanks Dan! The weather is looking perfect so I think we are going to do well.

PostPosted: Tue Sep 20, 2011 12:25 pm
by solaryellow
NCPaul wrote:What do you mean by reverse flow? That smoker will have no trouble doing a 100 pounds of kielbasa. :D


Image

See how the chimney is on the same side as the firebox? There is a plate that runs almost the entire length of the smoke chamber and stops 14" from the far left side. When the heat and smoke enter the smoke chamber it has to go all the way down the left side and then back across to the right hand side to exit. This heats up the plate and provides even temperatures from end to end. Most offset smokers have the chimney on the opposite side of the firebox and since heat rises you often get uneven temps from end to end without adding baffles and tuning plates.

Image

Here is a picture of the reverse flow plate as we constructed it.

Image

Image

And yes, it sure will hold that amount of kielbasa. :D

Image

PostPosted: Wed Sep 21, 2011 6:16 pm
by vagreys
Pitt's & Spitt's uses a reverse flow baffle in their offset designs, although it doesn't run back to the firebox, and instead makes another turn through the horizontal smoker and then exits through the vertical smoker at the opposite end from the firebox.

Neat design.

PostPosted: Wed Sep 21, 2011 6:56 pm
by solaryellow
Thanks Tom!

We put a damper in place to control the heat and smoke going from the smoke chamber to the warming box. It works pretty well too.

Image

PostPosted: Wed Sep 21, 2011 7:00 pm
by kimgary
Nice job and nice welding.

What paint finish do you use?

Regards Gazza.

PostPosted: Wed Sep 21, 2011 7:15 pm
by solaryellow
We applied Ospho to convert the rust and then painted with 2 coats of Thurmalox 270. I forgot to order thinner at the time so we brushed it on instead of spraying it.

Ospho - http://www.ospho.com/

Thurmalox 270 - http://www.stovepaint.com/

PostPosted: Wed Sep 21, 2011 7:47 pm
by DanMcG
Whatt Joel no bar napkins to draw your trailer design on, so ya had to use the smoker?

PostPosted: Wed Sep 21, 2011 8:47 pm
by solaryellow
Pretty much. :lol:

Gotta keep the expenses down. :wink:

PostPosted: Sun Sep 25, 2011 4:42 pm
by culinairezaken
That's what i call a smoker!

I feel kind a silly with a 30inch smoker....

PostPosted: Mon Sep 26, 2011 1:28 am
by solaryellow
culinairezaken wrote:That's what i call a smoker!

I feel kind a silly with a 30inch smoker....


My favorite smoker is still my ugly drum smoker. The UDS is like the wife or girlfriend we wish we could all have (easy to operate and not needing a whole lot of attention) while the one above is like the wife or girlfriend we all have (constantly needing attention). :lol:

This little fella was the highlight of the day though. He wouldn't stop gnawing on that rib for anything in the world.

Image

PostPosted: Thu Sep 29, 2011 6:58 pm
by culinairezaken
Last picture is absolutely the best!